Search results for "thermal [radiation mechanism]"
showing 10 items of 2571 documents
Influence of soil water content on the thermal infrared emissivity of bare soils. Implication for land surface temperature determination.
2007
[1] The influence of soil water content in thermal infrared emissivity is a known fact but has been poorly studied in the past. A laboratory study for quantifying the dependence of emissivity on soil moisture was carried out. Six samples of surface horizons of different soil types were selected for the experiment. The gravimetric method was chosen for determining the soil moisture, whereas the emissivity was measured at different soil water contents using the two-lid variant of the box method. As a result, the study showed that emissivity increases from 1.7% to 16% when water content becomes higher, especially in sandy soils in the 8.2–9.2 μm range. Accordingly, a set of equations was deriv…
The Influence of Land Surface Temperature in Evapotranspiration Estimated by the S-SEBI Model
2020
Evapotranspiration (ET) is one of the least understood components of the hydrological cycle. Its applications are varied, from agricultural, ecological and hydrological monitoring, to control of the evolution of climate change. The goal of this work was to analyze the influence that uncertainties in the estimate of land surface temperature (Ts) can cause on ET estimates by S-SEBI model in the Pampa biome area. Also, the specificities of native grassland of Pampa biome related to energy balance were analyzed. The results indicate that the daily evapotranspiration is higher when the pixel Ts is lower, which also shows the influence of land use on the variability of ET. The results demonstrate…
Evaluation of Surface Temperature and Emissivity Derived from ASTER Data: A Case Study Using Ground-Based Measurements at a Volcanic Site
2010
Abstract The land surface temperature (LST) and emissivity (LSE) derived from Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data were evaluated in a low spectral contrast volcanic site at an altitude of 2000 m on the island of Tenerife, Spain. The test site is almost flat, thermally homogeneous, and without vegetation cover or variation in its surface composition. ASTER data correspond to six scenes, under both day- and nighttime conditions during 2008. This case study analyzes the impacts of the sources of inaccuracies using the temperature–emissivity separation (TES) algorithm. Uncertainties associated with inaccurate atmospheric correction were minimized by means…
Temperature and Emissivity Separation From MSG/SEVIRI Data
2014
In this paper, we analyze the feasibility of applying the temperature and emissivity separation (TES) algorithm to thermal-infrared data acquired with three bands of the Spinning Enhanced Visible and Infrared Imager (SEVIRI) onboard the Meteosat Second Generation platform (SEVTES). The performance of the SEVTES algorithm was tested using data simulated over different atmospheric conditions and surface emissivities, with errors around 1.5% for emissivity and 1.5 K for temperature when atmospheric correction is accurate enough. In contrast, errors on land-leaving radiances higher than 2% or uncertainties on total atmospheric water vapor amount higher than 5% lead to errors on emissivity highe…
Beating Darwin-Bragg losses in lab-based ultrafast x-ray experiments
2017
The use of low temperature thermal detectors for avoiding Darwin-Bragg losses in lab-based ultrafast experiments has begun. An outline of the background of this new development is offered, showing the relevant history and initiative taken by this work. (C) 2017 Author(s). Funding Agencies|Knut and Alice Wallenberg Foundation; ERC [226136]; Finnish Funding Agency for Technology and Innovation TEKES; Academy of Finland [260880]; NIST Innovations in Measurement Science program; DOE Office of Basic Energy Sciences
Atomic layer deposition of polyimide thin films
2007
The atomic layer deposition (ALD) of different polyimide thin films has been studied. We have demonstrated self-limiting ALD deposition of PMDA–DAH, PMDA–EDA, PMDA–ODA and PMDA–PDA thin films at 160 °C. The maximum deposition rate of 5.8 A cycle−1 was obtained for the PMDA–DAH process. Although the deposition rate was high at 160 °C, a sudden decrease was observed when the temperature was increased. Regardless of the process studied, no film growth was obtained at 200 °C or above. Deposited polyimide films were analysed by FTIR, AFM and TOF-ERDA. According to the FTIR measurements, imide bonds were formed already in as-deposited films indicating polyimide formation without any additional th…
The influence of thin hard coatings on frictional behaviour in the orthogonal cutting process
2000
New knowledge about the tribological response deriving from the interaction of the substrate/coating-chip system, with special attention to the orthogonal cutting process when chatter-free end turning using natural contact tools, is developed. In order to evaluate the frictional behaviour of this process under modified contact conditions, experimental investigations including the contact temperature, the contact loads, friction and the frictional heat flux per unit area were carried out. In contrast to the most obvious approach, the coefficient of sliding friction versus the cutting speed, the contact temperature, the normal pressure and the interface control factor is considered. A number …
Assessing the electricity consumption of outdoor lighting systems in the presence of automatic control: The OL-BAC factors method
2020
Abstract Building automation systems are able to influence significantly buildings’ energy performance. The BAC factors method, presented for the first time by the International Standard EN 15232, is the most used and simple instrument for evaluating the impact of such systems in terms of reduction of the electrical and thermal energy consumption of buildings services. Nevertheless, Standard EN 15232 does not take into consideration the automation of lighting systems serving buildings’ external areas like passages, gardens, entrance walkways, etc. In some cases, such areas can be very extended and, as a consequence, responsible for a not negligible percentage of the overall electricity cons…
Chiral donor–π-acceptor azobenzene dyes
2009
Abstract Four chiral donor–π-acceptor azobenzene dye conjugates were synthesized and characterized. Chiral moieties, namely (S)-(+)-2-(6-methoxy-2-naphthyl)propionic acid (naproxen) and (S)-2-aminopropionic acid ( l -alanine), were attached to either the donor end or the acceptor site of the azo compound using ester or amide bonds, respectively. The structures of the molecules were verified using 1H NMR, 13C NMR and ESI TOF mass spectrometry; spectral properties were evaluated with UV–vis and CD spectrometry whilst thermal stability was determined by TGA. The compounds displayed a broad absorption maximum in the visible region between 433 and 483 nm. All compounds showed relatively high the…
Building integrated solar thermal design: assessment of performances of a low cost solar wall in a typical Italian building
2016
Abstract Present work deals with the topic of building integration of solar thermal collector (BIST) as a refurbishment measure. Such equipment, more than its main function as heating generator, plays a specific role as a building component (envelope finishes, thermal insulation layer, roof cover etc). Consequently, from a heat transfer point of view, an integrated component affects twice the global building balance: supporting the thermal plant (i.e. providing heat for final uses) and modifying the wall heat-transfer pattern (i.e. reducing thermal losses). In turn, the collector performance itself is influenced by the wall structure (back losses reduction). Present work proposes a method f…